Friday 15 December 2017

House Stark front door knocker - 3D Printed

► House Stark door knocker - Game of Thrones front door - 3D Printed

Please read the dimensions carefully as all are in mm and are approximate!

Dimensions below for body only (Handle not included)

► SMALL L100xW65XD90
► MEDIUM L130xW80XD110
► LARGE L155xW90XD130


 

#gameofthrones #got #housestark #stark #etsy #etsyseller #etsystore #kingofthenorth #household #frontdoor

www.awoodco.co.uk







Monday 11 December 2017

So, the Stark door knocker - just how I imaged it, if you saw my last 3D post. This will be available in our shop very soon.
#etsy https://goo.gl/sc3pEk

A bit more with the spray paint to get a weathered look - but all in all, I think a very good print.


Friday 8 December 2017

Low poly #3Dprinted door knocker - House of #Stark

3D printed door knocker - House of #stark.  Coming to a door near you soon.  Well, 19 hours in fact (print time)

As you can see, this has 2 fixings to allow for screws.  An apt product for the House of Stark

I will at some point be doing door knockers for the other #gameofthrones houses #Baratheon #Lannister #Targaryen #Martell #Tully #Greyjoy #Arryn #Tyrell

I could have kept the detail for the sigil but it looked a lot cooler low poly.  Also didn't want to go with the standard in the mouth knocker, as with this being low poly - limited detail would have been lost.

This is actually quite large being 13.5 CM from nose to the backplate, 20.5 CM from top to bottom of knocker and 9 CM wide.

Anyway, keep an eye on my store Aurora Woodworking Co over on #etsy #etsyseller #etsystore - this will be ready for sale in a couple of days



Website Aurora Woodworking Co

Thursday 7 December 2017

House Stark Sigil - Game of Thrones

Just started shopping for #christmas?  Someone you know a big #gameofthrones #fan?  Take a look at our #stark #sigils on #etsy Large House of Stark - Game of Thrones Sigil - 3D Printed

we can #3DPrint #house you like and we can also take #custom orders.

Take a look at our 3d printing service










#houseBaratheon, #houseLannister, #houseTargaryen, #houseMartell, #houseTully, #houseStark, #houseGreyjoy, #houseArryn, #houseTyrell

Printing problems


The problem with printing is that you can spend a fair few hours printing and after a night you come down in the morning to a ball of mess, or, there might be imperfections in the print that weren't visible in your 3D software.


However, as always, there's always room for improvement.  Watch this space!










#gotforlife #gameofthrones #aryastark #catspaw #gotseason7 #nedstark #housestark 
#houseBaratheon, #houseLannister, #houseTargaryen, #houseMartell, #houseTully, #houseStark, #houseGreyjoy, #houseArryn, #houseTyrell

Tuesday 5 December 2017

Dremel Ideabuilder 3D40

As I write this blog I have my main weapon running in the background, the #DremelIdeabuilder3D40.  If there's anyone out there that's on the verge of going with one - I would highly recommend it! 

The reason I'm writing this is because I've had this 'dream machine' for nearly 3 months now and I have perfected my #3dprints with 2 little helpers....#Frogtape multi surface & #Prittstick.

The #Dremel comes with a build plate and a thick black adhesive surface that you attach to the glass/perspex. They also give you (I think) 3 build tape sheets that I think is supposed to be scotch tape - but it's pants.

So with my #prittstick, I covered the black surface with a liberal layer of glue and then added the green multi surface frog tape being careful not to overlap (except for the last row near the edge).  After a couple of minutes of allowing the tape/glue to set - I then added another layer of glue on top of the frog tape.

That's it!  There's nothing else left to do except print.  The glue on the top layer does set, but with the heat of the plastic, this melts into the glue giving  good adhesion.  I find that I can get around 10 prints before I have to renew at least one row of frog tape.

I do however always print with a raft and without this little trick I always had a curl in at least one of the print corners.  If you have 8 hours prints like I do and come down in the morning to a ball of mess, at least try it.